.png)
Story
With the use of Wiznet’s W5100S-EVB-PICO and Peizo Buzzer will paying the musical notes of selected song via PWM
This project is based on Wiznet’s W5100S-EVB_PICO with circuitpython,Its just a small project of showcasing interfacing Buzzer and playing musical notes by contolling PWM pins in W5100s-EVB-PICO board via Web server.
Features of W5100S-EVB-PICO
RP2040 microcontroller with 2MByte Flash
- Dual-core cortex M0+ at up to 133MHz
- 264kByte multi-bank high performance SRAM
- External Quad-SPI Flash with eXecute In Place (XIP)
- High performance full-crossbar bus fabric
30 multi-function General Purpose IO (4 can be used for ADC)
- 1.8-3.3V IO Voltage (NOTE. Pico IO voltage is fixed at 3.3V)
- 30 multi-function General Purpose IO (4 can be used for ADC)1.8-3.3V IO Voltage (NOTE. Pico IO voltage is fixed at 3.3V)
- 12-bit 500ksps Analogue to Digital Converter (ADC)
Various digital peripherals
- 2 × UART, 2 × I2C, 2 × SPI, 16 × PWM channels
- 1 × Timer with 4 alarms, 1 × Real Time Counter
- Various digital peripherals2 × UART, 2 × I2C, 2 × SPI, 16 × PWM channels1 × Timer with 4 alarms, 1 × Real Time Counter
- 2 × Programmable IO (PIO) blocks, 8 state machines total
- Flexible, user-programmable high-speed IO
- Can emulate interfaces such as SD Card and VGA
- RP2040 microcontroller with 2MByte FlashDual-core cortex M0+ at up to 133MHz264kByte multi-bank high performance SRAMExternal Quad-SPI Flash with eXecute In Place (XIP)High performance full-crossbar bus fabric30 multi-function General Purpose IO (4 can be used for ADC)1.8-3.3V IO Voltage (NOTE. Pico IO voltage is fixed at 3.3V)12-bit 500ksps Analogue to Digital Converter (ADC)Various digital peripherals2 × UART, 2 × I2C, 2 × SPI, 16 × PWM channels1 × Timer with 4 alarms, 1 × Real Time Counter2 × Programmable IO (PIO) blocks, 8 state machines totalFlexible, user-programmable high-speed IOCan emulate interfaces such as SD Card and VGA
Includes W5100S
- Supports Hardwired Internet Protocols: TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoE
- Supports 4 Independent Hardware SOCKETs simultaneously
- Internal 16 Kbytes Memory for TX/ RX Buffers
- SPI Interface
- Includes W5100SSupports Hardwired Internet Protocols: TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoESupports 4 Independent Hardware SOCKETs simultaneouslyInternal 16 Kbytes Memory for TX/ RX BuffersSPI Interface
- Micro-USB B port for power and data (and for reprogramming the Flash)
- 40 pin 21×51 ‘DIP’ style 1mm thick PCB with 0.1″ through-hole pins also with edge castellations
- 3-pin ARM Serial Wire Debug (SWD) port
- 10 / 100 Ethernet PHY embedded
Supports Auto Negotiation
- Full / Half Duplex
- 10 / 100 Based
- Supports Auto NegotiationFull / Half Duplex10 / 100 Based
- Built-in RJ45(RB1-125BAG1A)
- Built-in LDO (LM8805SF5-33V)
Hardware Specification
Pin-out
W5100S-EVB-Pico pinout is directly connected to the GPIO of RP2040 as shown in the picture above. It has the same pinout as the Raspberry Pi Pico board. However, GPIO16, GPIO17, GPIO18, GPIO19, GPIO20, GPIO21 are connected to W5100S inside the board. These pins enable SPI communication with W5100S to use Ethernet function. If you are using the Ethernet function, these pins cannot be used for any other purpose.
For getting started with W5100s-EVB-PICO board refer the link https://github.com/Wiznet/RP2040-HAT-CircuitPython/blob/master/Ethernet%20Example%20Getting%20Started%20%5BCircuitpython%5D.md
Connections
Connecting the Buzzer one End to GND(Ground) pin of EVB and one end to GPIO3(pin number 5) of EVB.
Future work
Planning to play mp3 music with this setup
Result
This the web server page for playing musics
Terminal output
COMMENTS